ApplianceErrors.com

Maytag Dryer Error Code E2

Reviewed by the ApplianceErrors Editorial Team · Verified against manufacturer service documentation · Last verified: July 19, 2026
⚠ Medium Severity 🔧🔧 Moderate DIY

Thermistor short circuit — temperature sensor failure

The most common cause of the E2 error on a Maytag dryer is thermistor shorted (~70% of cases); start with: test the thermistor.

💰 DIY cost: $15–$40 👨‍🔧 Pro cost: $150–$280 Save $135+ by doing it yourself
Maytag Dryer error code E2 on the display panel
How the E2 code appears on a Maytag dryer display

What Does Error Code E2 Mean on a Maytag Dryer?

Thermistor short circuit — temperature sensor failure.

E2 fires when the control board measures abnormally low resistance on the thermistor circuit — typically under about 500 ohms versus a normal ~10k ohms at room temperature. That out-of-range reading is interpreted as a short, so the control flags an invalid temperature signal and halts heating. Unlike E1, which indicates an open circuit (very high or infinite resistance), E2 points to a shorted sensor or wiring shorted to the chassis rather than a broken connection or loss of continuity.

Models affected: Maytag electronic-display dryers with a thermistor-based temperature circuit, including models such as MEDC465HW, MED7230HW, and MED4500MW
What owners report: Owners commonly report E2 appearing at the start of a cycle or partway through, sometimes alongside no-heat or short-cycling complaints. A pinched or melted wire behind the drum can mimic a bad sensor, so many find checking the harness before buying parts saves a needless thermistor swap.

What Causes Error Code E2?

Here are the most common causes in order of frequency. Start with the most likely cause before moving to the next:

  1. 1
    Thermistor shorted 70% of cases
  2. 2
    Wiring pinched/shorted to chassis 20% of cases
  3. 3
    Control board sensor circuit fault 10% of cases

How to Fix Maytag Dryer Error Code E2

🔧🔧 Moderate DIY Est. time: 30–60 min
⚡ Safety first: Unplug the appliance before opening any panels or touching internal components.
  1. 1

    Test the thermistor

    Room temperature should read ~10k ohms. Near 0 ohms = shorted.

    🔩 Multimeter
  2. 2

    Inspect the wiring

    Look for pinched or melted wiring shorting the thermistor.

  3. 3

    Replace the thermistor

    A shorted thermistor cannot be repaired.

    🔩 Maytag dryer thermistor ($15–$40)
    ⚠️ Unplug before servicing.

How to Reset Error Code E2

After replacing the thermistor, unplug 1 minute then restart.

Note: If the error returns after resetting, the underlying issue has not been resolved. Work through the fix steps above.

Full Maytag dryer reset guide → Enter diagnostic mode →

Did this guide fix your appliance?

When to Call a Professional

If a new thermistor reads shorted, the wiring harness has a short to ground.

Average professional repair cost for this issue: $150–$280

Related Error Codes

E1
Thermistor open circuit — temperature sensor failure
⚠ Medium Severity
F22
Outlet thermistor (temperature sensor) failure
⚠ Medium Severity
F24
Inlet thermistor failure — temperature sensor fault
⚠ Medium Severity

Same Code on Other Brands

Error code E2 appears on these other brands too. See every brand that shows E2 →

Broan-NuTone logo
Broan-NuTone Range Hood E02
Fan motor failure — motor not running
Speed Queen logo
Speed Queen Washing Machine E2
Motor feedback error — motor control fault
Fisher & Paykel logo
Fisher & Paykel Washing Machine E2
Motor controller fault
Haier logo
Haier Washing Machine E2
Drain error — water not draining

Find Replacement Parts

Use these links to find the exact replacement parts for your Maytag Dryer:

🔩
Search PartSelect
Maytag Dryer repair parts
🔧
Search RepairClinic
Step-by-step video guides

External links — ApplianceErrors.com is not affiliated with these retailers.

More Maytag Dryer Error Codes

F01 Electronic control board failure F06 Drive motor failure — drum not turning AF Restricted airflow — blocked vent (safety shutdown) F26 Drive motor failure — drum not turning F29 Moisture sensor failure — auto-dry not working F30 Restricted airflow / moisture sensor — stored airflow fault

Frequently Asked Questions

Can I keep using my Maytag Dryer when error E2 appears? +
You often can for a cycle or two, but the sensor issue behind E2 will keep interrupting normal operation until it is fixed. Plan the repair rather than ignoring the code.
What most commonly causes E2 on a Maytag Dryer? +
Across reported Maytag dryer repairs, the most frequent is thermistor shorted (70% of cases), wiring pinched/shorted to chassis (20%), then control board sensor circuit fault (10%). Check them in that order before replacing any parts.
E2 keeps coming back after a reset — what should I check next? +
A reset only clears the stored E2 fault; if it returns, the sensor problem is still present. Move on to the physical checks — test the thermistor, then inspect the wiring — since the code will reappear until the root cause is resolved. This is a moderate job — a multimeter and some disassembly are usually involved.
How much does it cost to fix Maytag Dryer error E2? +
A DIY repair typically runs $15–$40 in parts, versus $150–$280 for a professional service call, so handling it yourself saves around $135. Expect the work to take roughly 30–60 minutes.
Which Maytag Dryer models show error E2? +
E2 is documented on Maytag electronic-display dryers with a thermistor-based temperature circuit, including models such as MEDC465HW, MED7230HW, and MED4500MW. Other units sharing the same control platform can display it too, so the fixes here generally transfer across the series.

Sources & References

Content verified against manufacturer service documentation. Last verified: July 19, 2026.

← All Maytag Dryer Error Codes ← All Maytag Error Codes