Maytag Dryer Error Code F22

Reviewed by the ApplianceErrors Editorial Team · Verified against manufacturer service documentation · Last verified: June 10, 2026

⚠ Medium Severity 🔧🔧 Moderate DIY

Outlet thermistor (temperature sensor) failure

The most common cause of the F22 error on a Maytag dryer is thermistor open circuit (~70% of cases); start with: test thermistor.

💰 DIY cost: $15–$40 👨‍🔧 Pro cost: $150–$280 Save $135+ by doing it yourself

Maytag Dryer error code F22 on the display panel — How the F22 code appears on a Maytag dryer display

What Does Error Code F22 Mean on a Maytag Dryer?

Outlet thermistor (temperature sensor) failure.

F22 fires when the control detects an out-of-range or open resistance reading from the outlet (exhaust) thermistor, the sensor that tracks outgoing air temperature. Because the board can no longer confirm safe heat levels, it halts drying or refuses to heat. This differs from a shorted-sensor reading and from thermal-fuse or heating-element faults; F22 points specifically at the thermistor circuit — the sensor itself, a loose connector, or heat-damaged wiring on the blower housing.

Models affected: Maytag electric and gas dryers with electronic controls that monitor exhaust air temperature, including models such as MEDC465HW, MED7230HW, and MED4500MW

What owners report: Owners commonly report this code appearing mid-cycle or when the dryer runs but won't heat, and it often clears after reseating the thermistor connector. A quick resistance check at room temperature (roughly 10k–12k ohms) usually confirms whether the inexpensive sensor is the culprit before ordering parts.

What Causes Error Code F22?

Here are the most common causes in order of frequency. Start with the most likely cause before moving to the next:

1

Thermistor open circuit 70% of cases
2

Connector loose 20% of cases
3

Wiring damaged by heat 10% of cases

How to Fix Maytag Dryer Error Code F22

🔧🔧 Moderate DIY Est. time: 30–60 min

⚡ Safety first: Unplug the appliance before opening any panels or touching internal components.

1

Test thermistor

Room temp: ~10k–12k ohms.

🔩 Multimeter
2

Replace thermistor

Located in exhaust duct inside cabinet.

🔩 Maytag dryer thermistor ($15–$40)

How to Reset Error Code F22

After replacement, unplug 1 minute then restart.

Note: If the error returns after resetting, the underlying issue has not been resolved. Work through the fix steps above.

Full Maytag dryer reset guide → Enter diagnostic mode →

Did this guide fix your appliance?

When to Call a Professional

If new thermistor and error persists, control board sensor input failed.

Average professional repair cost for this issue: $150–$280

Same Code on Other Brands

Error code F22 appears on these other brands too. See every brand that shows F22 →

Whirlpool Washing Machine F22

Door lock failure — door did not lock

Whirlpool Dryer F22

Outlet thermistor failure

Amana Dryer F22

Outlet thermistor failure

Kenmore Dryer F22

Outlet thermistor failure — reading open

Find Replacement Parts

Use these links to find the exact replacement parts for your Maytag Dryer:

🔩

Search PartSelect

Maytag Dryer repair parts

🔧

Search RepairClinic

Step-by-step video guides

External links — ApplianceErrors.com is not affiliated with these retailers.

More Maytag Dryer Error Codes

F01 Electronic control board failure F06 Drive motor failure — drum not turning AF Restricted airflow — blocked vent (safety shutdown) E1 Thermistor open circuit — temperature sensor failure E2 Thermistor short circuit — temperature sensor failure F24 Inlet thermistor failure — temperature sensor fault

Frequently Asked Questions

Can I keep using my Maytag Dryer when error F22 appears? +

You often can for a cycle or two, but the sensor issue behind F22 will keep interrupting normal operation until it is fixed. Plan the repair rather than ignoring the code.

What most commonly causes F22 on a Maytag Dryer? +

Across reported Maytag dryer repairs, the most frequent is thermistor open circuit (70% of cases), connector loose (20%), then wiring damaged by heat (10%). Check them in that order before replacing any parts.

F22 keeps coming back after a reset — what should I check next? +

A reset only clears the stored F22 fault; if it returns, the sensor problem is still present. Move on to the physical checks — test thermistor, then replace thermistor — since the code will reappear until the root cause is resolved. This is a moderate job — a multimeter and some disassembly are usually involved.

How much does it cost to fix Maytag Dryer error F22? +

A DIY repair typically runs $15–$40 in parts, versus $150–$280 for a professional service call, so handling it yourself saves around $135. Expect the work to take roughly 30–60 minutes.

Which Maytag Dryer models show error F22? +

F22 is documented on Maytag electric and gas dryers with electronic controls that monitor exhaust air temperature, including models such as MEDC465HW, MED7230HW, and MED4500MW. Other units sharing the same control platform can display it too, so the fixes here generally transfer across the series.

Sources & References

• Maytag Product Help — official manufacturer documentation
• Our editorial & verification policy

Content verified against manufacturer service documentation. Last verified: June 10, 2026.

← All Maytag Dryer Error Codes ← All Maytag Error Codes