ApplianceErrors.com

Maytag Dryer Error Code F24

Reviewed by the ApplianceErrors Editorial Team · Verified against manufacturer service documentation · Last verified: July 19, 2026
⚠ Medium Severity 🔧🔧 Moderate DIY

Inlet thermistor failure — temperature sensor fault

The most common cause of the F24 error on a Maytag dryer is inlet thermistor out of range (~70% of cases); start with: test the thermistor.

💰 DIY cost: $15–$40 👨‍🔧 Pro cost: $150–$280 Save $135+ by doing it yourself
Maytag Dryer error code F24 on the display panel
How the F24 code appears on a Maytag dryer display

What Does Error Code F24 Mean on a Maytag Dryer?

Inlet thermistor failure — temperature sensor fault.

F24 fires when the control reads a resistance from the inlet thermistor that falls outside its valid window — typically an open (very high resistance) or shorted (very low) circuit rather than a plausible temperature. Without a trustworthy inlet reading, the board cannot regulate heat safely, so it flags the fault. Unlike outlet-sensor or cycling-thermostat codes, F24 points specifically to the inlet air-temperature sensor, its connector, or its wiring, not to the heater or vent restriction itself.

Models affected: Maytag electric and gas dryers with electronic controls that monitor inlet air temperature, including models such as MEDC465HW, MED7230HW, and MED4500MW
What owners report: Owners commonly report F24 appearing at the start of or partway through a cycle, sometimes with heating cutting out. A loose or corroded connector can falsely trigger it, so reseating the plug is a frequent quick win before the sensor itself is replaced.

What Causes Error Code F24?

Here are the most common causes in order of frequency. Start with the most likely cause before moving to the next:

  1. 1
    Inlet thermistor out of range 70% of cases
  2. 2
    Connector loose 20% of cases
  3. 3
    Wiring damaged 10% of cases

How to Fix Maytag Dryer Error Code F24

🔧🔧 Moderate DIY Est. time: 30–60 min
⚡ Safety first: Unplug the appliance before opening any panels or touching internal components.
  1. 1

    Test the thermistor

    At room temperature the thermistor should read roughly 10k ohms.

    🔩 Multimeter
  2. 2

    Reseat the connector

    Check the inlet thermistor connector.

  3. 3

    Replace the thermistor

    Install a new inlet thermistor.

    🔩 Maytag dryer thermistor ($15–$40)
    ⚠️ Unplug before servicing.

How to Reset Error Code F24

After replacing the thermistor, unplug 1 minute then restart.

Note: If the error returns after resetting, the underlying issue has not been resolved. Work through the fix steps above.

Full Maytag dryer reset guide → Enter diagnostic mode →

Did this guide fix your appliance?

When to Call a Professional

If a new thermistor and F24 persists, the control board sensor input has failed.

Average professional repair cost for this issue: $150–$280

Related Error Codes

F22
Outlet thermistor (temperature sensor) failure
⚠ Medium Severity
E1
Thermistor open circuit — temperature sensor failure
⚠ Medium Severity
E2
Thermistor short circuit — temperature sensor failure
⚠ Medium Severity

Same Code on Other Brands

Error code F24 appears on these other brands too. See every brand that shows F24 →

Whirlpool logo
Whirlpool Dryer F24
Inlet/exhaust thermistor (temperature sensor) out of range
Miele logo
Miele Dishwasher F24
Heating circuit fault — heater relay or temperature sensor

Find Replacement Parts

Use these links to find the exact replacement parts for your Maytag Dryer:

🔩
Search PartSelect
Maytag Dryer repair parts
🔧
Search RepairClinic
Step-by-step video guides

External links — ApplianceErrors.com is not affiliated with these retailers.

More Maytag Dryer Error Codes

F01 Electronic control board failure F06 Drive motor failure — drum not turning AF Restricted airflow — blocked vent (safety shutdown) F26 Drive motor failure — drum not turning F29 Moisture sensor failure — auto-dry not working F30 Restricted airflow / moisture sensor — stored airflow fault

Frequently Asked Questions

Can I keep using my Maytag Dryer when error F24 appears? +
You often can for a cycle or two, but the sensor issue behind F24 will keep interrupting normal operation until it is fixed. Plan the repair rather than ignoring the code.
What most commonly causes F24 on a Maytag Dryer? +
Across reported Maytag dryer repairs, the most frequent is inlet thermistor out of range (70% of cases), connector loose (20%), then wiring damaged (10%). Check them in that order before replacing any parts.
F24 keeps coming back after a reset — what should I check next? +
A reset only clears the stored F24 fault; if it returns, the sensor problem is still present. Move on to the physical checks — test the thermistor, then reseat the connector — since the code will reappear until the root cause is resolved. This is a moderate job — a multimeter and some disassembly are usually involved.
How much does it cost to fix Maytag Dryer error F24? +
A DIY repair typically runs $15–$40 in parts, versus $150–$280 for a professional service call, so handling it yourself saves around $135. Expect the work to take roughly 30–60 minutes.
Which Maytag Dryer models show error F24? +
F24 is documented on Maytag electric and gas dryers with electronic controls that monitor inlet air temperature, including models such as MEDC465HW, MED7230HW, and MED4500MW. Other units sharing the same control platform can display it too, so the fixes here generally transfer across the series.

Sources & References

Content verified against manufacturer service documentation. Last verified: July 19, 2026.

← All Maytag Dryer Error Codes ← All Maytag Error Codes