ApplianceErrors.com

Maytag Dryer Error Code E1

Reviewed by the ApplianceErrors Editorial Team · Verified against manufacturer service documentation · Last verified: July 19, 2026
⚠ Medium Severity 🔧🔧 Moderate DIY

Thermistor open circuit — temperature sensor failure

The most common cause of the E1 error on a Maytag dryer is thermistor open circuit (~70% of cases); start with: test the thermistor.

💰 DIY cost: $15–$40 👨‍🔧 Pro cost: $150–$280 Save $135+ by doing it yourself
Maytag Dryer error code E1 on the display panel
How the E1 code appears on a Maytag dryer display

What Does Error Code E1 Mean on a Maytag Dryer?

Thermistor open circuit — temperature sensor failure.

E1 fires when the control board's sensor input reads an open circuit from the thermistor — resistance far above the expected ~10k ohms at room temperature, often exceeding 50k ohms or reading infinite. Unable to measure exhaust air temperature, the control disables the heater as a safety measure. This distinguishes E1 from E2, which signals a shorted (low-resistance) thermistor, and from F22/F24 codes tied to broader temperature-sensing or control-input faults rather than a simple open circuit.

Models affected: Maytag electric dryers with electronic controls and a thermistor-based temperature system, including models such as MEDC465HW, MED7230HW, and MED4500MW
What owners report: Owners commonly report E1 appearing shortly after a cycle starts, sometimes with the drum turning but no heat. A loose or heat-fatigued connector at the thermistor is a frequent false trigger, so many find that simply reseating the plug clears the code before any part is replaced.

What Causes Error Code E1?

Here are the most common causes in order of frequency. Start with the most likely cause before moving to the next:

  1. 1
    Thermistor open circuit 70% of cases
  2. 2
    Connector loose 20% of cases
  3. 3
    Wiring damaged by heat 10% of cases

How to Fix Maytag Dryer Error Code E1

🔧🔧 Moderate DIY Est. time: 30–60 min
⚡ Safety first: Unplug the appliance before opening any panels or touching internal components.
  1. 1

    Test the thermistor

    At room temperature the thermistor should read roughly 10k ohms. Infinite resistance = open.

    🔩 Multimeter
  2. 2

    Check the connector

    Reseat the thermistor connector.

  3. 3

    Replace the thermistor

    Located on the blower housing or exhaust duct.

    🔩 Maytag dryer thermistor ($15–$40)
    ⚠️ Unplug before servicing.

How to Reset Error Code E1

After replacing the thermistor, unplug 1 minute then restart.

Note: If the error returns after resetting, the underlying issue has not been resolved. Work through the fix steps above.

Full Maytag dryer reset guide → Enter diagnostic mode →

Did this guide fix your appliance?

When to Call a Professional

If a new thermistor and E1 persists, the control board sensor input has failed.

Average professional repair cost for this issue: $150–$280

Related Error Codes

E2
Thermistor short circuit — temperature sensor failure
⚠ Medium Severity
F22
Outlet thermistor (temperature sensor) failure
⚠ Medium Severity
F24
Inlet thermistor failure — temperature sensor fault
⚠ Medium Severity

Same Code on Other Brands

Error code E1 appears on these other brands too. See every brand that shows E1 →

LG logo
LG Dryer F9
Thermistor failure — temperature sensor not reading
LG logo
LG Dishwasher AE
Leakage detected — water found in base tray
GE Appliances logo
GE Appliances Dryer E1
Thermistor open — temperature sensor failure
Broan-NuTone logo
Broan-NuTone Range Hood E01
Fan motor overload — motor drawing excess current

Find Replacement Parts

Use these links to find the exact replacement parts for your Maytag Dryer:

🔩
Search PartSelect
Maytag Dryer repair parts
🔧
Search RepairClinic
Step-by-step video guides

External links — ApplianceErrors.com is not affiliated with these retailers.

More Maytag Dryer Error Codes

F01 Electronic control board failure F06 Drive motor failure — drum not turning AF Restricted airflow — blocked vent (safety shutdown) F26 Drive motor failure — drum not turning F29 Moisture sensor failure — auto-dry not working F30 Restricted airflow / moisture sensor — stored airflow fault

Frequently Asked Questions

Can I keep using my Maytag Dryer when error E1 appears? +
You often can for a cycle or two, but the sensor issue behind E1 will keep interrupting normal operation until it is fixed. Plan the repair rather than ignoring the code.
What most commonly causes E1 on a Maytag Dryer? +
Across reported Maytag dryer repairs, the most frequent is thermistor open circuit (70% of cases), connector loose (20%), then wiring damaged by heat (10%). Check them in that order before replacing any parts.
E1 keeps coming back after a reset — what should I check next? +
A reset only clears the stored E1 fault; if it returns, the sensor problem is still present. Move on to the physical checks — test the thermistor, then check the connector — since the code will reappear until the root cause is resolved. This is a moderate job — a multimeter and some disassembly are usually involved.
How much does it cost to fix Maytag Dryer error E1? +
A DIY repair typically runs $15–$40 in parts, versus $150–$280 for a professional service call, so handling it yourself saves around $135. Expect the work to take roughly 30–60 minutes.
Which Maytag Dryer models show error E1? +
E1 is documented on Maytag electric dryers with electronic controls and a thermistor-based temperature system, including models such as MEDC465HW, MED7230HW, and MED4500MW. Other units sharing the same control platform can display it too, so the fixes here generally transfer across the series.

Sources & References

Content verified against manufacturer service documentation. Last verified: July 19, 2026.

← All Maytag Dryer Error Codes ← All Maytag Error Codes