Fisher & Paykel Washing Machine Error Code E2

Reviewed by the ApplianceErrors Editorial Team · Verified against manufacturer service documentation · Last verified: June 10, 2026

⚠ High Severity 👨‍🔧 Call a Pro

Motor controller fault

The most common cause of the E2 error on a Fisher & Paykel washing machine is motor controller board failure (~50% of cases); start with: power cycle the washer.

💰 DIY cost: $0–$0 👨‍🔧 Pro cost: $250–$600 Save $250+ by doing it yourself

Fisher & Paykel Washing Machine error code E2 on the display panel — How the E2 code appears on a Fisher & Paykel washing machine display

What Does Error Code E2 Mean on a Fisher & Paykel Washing Machine?

Motor controller fault.

E2 fires when the motor controller board reads abnormal feedback from the brushless direct-drive system — either unexpected drive current, an out-of-range winding resistance in the stator, or an implausible rotor-position signal. The board halts the cycle to protect the electronics and windings from overheating. Unlike load-imbalance or lid faults, E2 points at the drive electronics or motor itself rather than the mechanics, so it typically persists once the basket attempts to turn even with a light, well-distributed load.

Models affected: Fisher & Paykel top-load washers using the SmartDrive brushless direct-drive motor, including the WH2424P1

What owners report: Owners commonly report E2 appearing right as the machine tries to spin, sometimes after a heavy or lopsided load. A power cycle and lighter load occasionally clears a one-off trip, but many find the code returns quickly, which usually points to a genuine controller or motor fault needing service.

What Causes Error Code E2?

Here are the most common causes in order of frequency. Start with the most likely cause before moving to the next:

1

Motor controller board failure 50% of cases
2

Motor stator failure 30% of cases
3

Rotor position sensor fault 20% of cases

How to Fix Fisher & Paykel Washing Machine Error Code E2

👨‍🔧 Call a Pro Est. time: 1–3 hours

⚡ Safety first: Unplug the appliance before opening any panels or touching internal components.

1

Power cycle the washer

Unplug for 10 minutes to reset the motor controller, then restore power and try a spin-only cycle.
2

Check for overloading

Remove half the load and redistribute bulky items; extreme overload can trigger motor-current protection.
3

Inspect for binding

Spin the basket by hand with power off; dragging, seized bearings, or jammed clothing can overload the controller.
4

Contact F&P service

Motor controller, stator, and rotor-position faults require model-specific diagnostics and parts.

How to Reset Error Code E2

Unplug the washer for 10 minutes, reduce the load, and restart on spin-only. If E2 returns as soon as the basket tries to turn, stop using the washer and book authorized service.

Note: If the error returns after resetting, the underlying issue has not been resolved. Work through the fix steps above.

Symptom guide: Washer not spinning →

Did this guide fix your appliance?

When to Call a Professional

Fisher & Paykel brushless motor systems are proprietary; if load and mechanical binding are ruled out, authorized service should test the controller, stator, and rotor sensor.

Average professional repair cost for this issue: $250–$600

Same Code on Other Brands

Error code E2 appears on these other brands too. See every brand that shows E2 →

Maytag Dryer E2

Thermistor short circuit — temperature sensor failure

Broan-NuTone Range Hood E02

Fan motor failure — motor not running

Speed Queen Washing Machine E2

Motor feedback error — motor control fault

Haier Washing Machine E2

Drain error — water not draining

Find Replacement Parts

Use these links to find the exact replacement parts for your Fisher & Paykel Washing Machine:

🔩

Search PartSelect

Fisher & Paykel Washing Machine repair parts

🔧

Search RepairClinic

Step-by-step video guides

External links — ApplianceErrors.com is not affiliated with these retailers.

More Fisher & Paykel Washing Machine Error Codes

E4 Water inlet fault — insufficient fill E5 Drain pump fault — drainage problem E6 Lid switch fault — lid not detected as closed (top-load models)

Frequently Asked Questions

Can I keep using my Fisher & Paykel Washing Machine when error E2 appears? +

It is not advisable. The washing machine may still power on, but running it while E2 is active can worsen the motor fault or damage related parts. Treat it as a soon-as-possible repair.

What most commonly causes E2 on a Fisher & Paykel Washing Machine? +

Across reported Fisher & Paykel washing machine repairs, the most frequent is motor controller board failure (50% of cases), motor stator failure (30%), then rotor position sensor fault (20%). Check them in that order before replacing any parts.

E2 keeps coming back after a reset — what should I check next? +

A reset only clears the stored E2 fault; if it returns, the motor problem is still present. Move on to the physical checks — power cycle the washer, then check for overloading — since the code will reappear until the root cause is resolved. This is a repair most owners hand to a technician.

How much does it cost to fix Fisher & Paykel Washing Machine error E2? +

A DIY repair typically runs $0–$0 in parts, versus $250–$600 for a professional service call, so handling it yourself saves around $250. Expect the work to take a full service visit.

Which Fisher & Paykel Washing Machine models show error E2? +

E2 is documented on Fisher & Paykel top-load washers using the SmartDrive brushless direct-drive motor, including the WH2424P1. Other units sharing the same control platform can display it too, so the fixes here generally transfer across the series.

Sources & References

• Fisher & Paykel Support — official manufacturer documentation
• Our editorial & verification policy

Content verified against manufacturer service documentation. Last verified: June 10, 2026.

← All Fisher & Paykel Washing Machine Error Codes ← All Fisher & Paykel Error Codes