Haier Washing Machine Error Code E2

Reviewed by the ApplianceErrors Editorial Team · Verified against manufacturer service documentation · Last verified: June 10, 2026

⚠ High Severity 🔧🔧 Moderate DIY

Drain error — water not draining

The most common cause of the E2 error on a Haier washing machine is pump filter clogged (~50% of cases); start with: clean pump filter.

💰 DIY cost: $0–$80 👨‍🔧 Pro cost: $150–$280 Save $150+ by doing it yourself

Haier Washing Machine error code E2 on the display panel — How the E2 code appears on a Haier washing machine display

What Does Error Code E2 Mean on a Haier Washing Machine?

Drain error — water not draining.

E2 fires when the control board runs the drain pump but the pressure sensor still senses water above the empty threshold after the allotted drain time, so the cycle pauses. Restricted flow is the usual trigger — a debris-clogged pump filter, kinked hose, or blocked standpipe — rather than the pump itself. This distinguishes E2 from a fill or water-inlet code like E1, which concerns water not entering the tub instead of failing to leave it.

Models affected: Haier front-load washers such as the HLC1700AXW, and other Haier models that use a drain pump and pressure sensor to confirm the tub has emptied.

What owners report: Owners commonly report E2 appearing near the end of a cycle when the drum stays full of water, often after washing lint-heavy loads or when a coin or clip reaches the pump filter. Many find that simply clearing the filter and straightening the drain hose resolves it, though a persistently sluggish drain can point to a failing pump.

What Causes Error Code E2?

Here are the most common causes in order of frequency. Start with the most likely cause before moving to the next:

1

Pump filter clogged 50% of cases
2

Drain hose kinked 25% of cases
3

Standpipe blocked 15% of cases
4

Pump motor failure 10% of cases

How to Fix Haier Washing Machine Error Code E2

🔧🔧 Moderate DIY Est. time: 30–60 min

⚡ Safety first: Unplug the appliance before opening any panels or touching internal components.

1

Clean pump filter

Access via lower front panel. Drain and clean.

⚠️ Have towels ready.
2

Check drain hose

No kinks; proper high-loop installation.
3

Test drain pump

If filter and hose are clear.

🔩 Haier drain pump ($35–$80)

How to Reset Error Code E2

After clearing the drain filter and hose, unplug the washer for 60 seconds, then run a Spin-only cycle to confirm the tub empties before starting a full wash.

Note: If the error returns after resetting, the underlying issue has not been resolved. Work through the fix steps above.

Symptom guide: Washer won't drain →

Did this guide fix your appliance?

When to Call a Professional

If pump motor fails, replace it.

Average professional repair cost for this issue: $150–$280

Related Error Codes

Water inlet error — no water detected

⚠ Medium Severity

Same Code on Other Brands

Error code E2 appears on these other brands too. See every brand that shows E2 →

Maytag Dryer E2

Thermistor short circuit — temperature sensor failure

Broan-NuTone Range Hood E02

Fan motor failure — motor not running

Speed Queen Washing Machine E2

Motor feedback error — motor control fault

Fisher & Paykel Washing Machine E2

Motor controller fault

Find Replacement Parts

Use these links to find the exact replacement parts for your Haier Washing Machine:

🔩

Search PartSelect

Haier Washing Machine repair parts

🔧

Search RepairClinic

Step-by-step video guides

External links — ApplianceErrors.com is not affiliated with these retailers.

More Haier Washing Machine Error Codes

E4 Door not closed or door lock failure E3 Motor error — drive motor fault E7 Water level sensor fault F7 Motor fault — drum motor not responding

Frequently Asked Questions

Can I keep using my Haier Washing Machine when error E2 appears? +

It is not advisable. The washing machine may still power on, but running it while E2 is active can worsen the drainage fault or damage related parts. Treat it as a soon-as-possible repair.

What most commonly causes E2 on a Haier Washing Machine? +

Across reported Haier washing machine repairs, the most frequent is pump filter clogged (50% of cases), drain hose kinked (25%), then standpipe blocked (15%). Check them in that order before replacing any parts.

E2 keeps coming back after a reset — what should I check next? +

A reset only clears the stored E2 fault; if it returns, the drainage problem is still present. Move on to the physical checks — clean pump filter, then check drain hose — since the code will reappear until the root cause is resolved. This is a moderate job — a multimeter and some disassembly are usually involved.

How much does it cost to fix Haier Washing Machine error E2? +

A DIY repair typically runs $0–$80 in parts, versus $150–$280 for a professional service call, so handling it yourself saves around $150. Expect the work to take roughly 30–60 minutes.

Which Haier Washing Machine models show error E2? +

E2 is documented on Haier front-load washers such as the HLC1700AXW, and other Haier models that use a drain pump and pressure sensor to confirm the tub has emptied.. Other units sharing the same control platform can display it too, so the fixes here generally transfer across the series.

Sources & References

• Haier Appliances Support — official manufacturer documentation
• Our editorial & verification policy

Content verified against manufacturer service documentation. Last verified: June 10, 2026.

← All Haier Washing Machine Error Codes ← All Haier Error Codes