Maytag Washing Machine Error Code F3E1

Reviewed by the ApplianceErrors Editorial Team · Verified against manufacturer service documentation · Last verified: July 19, 2026

⚠ Medium Severity 🔧🔧 Moderate DIY

Water level / pressure sensor fault

The most common cause of the F3E1 error on a Maytag washing machine is pressure sensor failure (~45% of cases); start with: check the pressure (air) hose.

💰 DIY cost: $25–$70 👨‍🔧 Pro cost: $150–$300 Save $125+ by doing it yourself

Maytag Washing Machine error code F3E1 on the display panel — How the F3E1 code appears on a Maytag washing machine display

What Does Error Code F3E1 Mean on a Maytag Washing Machine?

Water level / pressure sensor fault.

F3E1 fires when the control board reads a water-level pressure-sensor signal that falls outside its valid range, so it can no longer trust how much water is in the tub. This blocks reliable fill and drain decisions. Unlike F8E1, which points to an actual long-fill or water-supply problem, F3E1 is a sensor-side fault: the electrical signal itself, its wiring, or the air hose feeding pressure to the sensor is the issue rather than the incoming water.

Models affected: Top-load and front-load Maytag washers that use an analog water-level pressure sensor, roughly 2015 onward

What owners report: Owners commonly report this appearing at the start of a cycle or during fill, sometimes stopping the machine mid-wash. A pinched, disconnected, or moisture-clogged air hose is a frequent false trigger, and many find that reseating the hose plus a one-minute power cycle clears the code before any sensor replacement is needed.

What Causes Error Code F3E1?

Here are the most common causes in order of frequency. Start with the most likely cause before moving to the next:

1

Pressure sensor failure 45% of cases
2

Air hose to pressure sensor kinked or clogged 35% of cases
3

Wiring to sensor fault 20% of cases

How to Fix Maytag Washing Machine Error Code F3E1

🔧🔧 Moderate DIY Est. time: 30–60 min

⚡ Safety first: Unplug the appliance before opening any panels or touching internal components.

1

Check the pressure (air) hose

Inspect the hose from the tub to the sensor for kinks, leaks, or clogs.
2

Power cycle

Unplug for 1 minute.
3

Replace the pressure sensor

If the sensor has failed.

🔩 Maytag washer pressure sensor ($25–$70)

⚠️ Unplug before servicing.

How to Reset Error Code F3E1

Check the air hose and unplug 1 minute. Replace the pressure sensor if F3E1 persists.

Note: If the error returns after resetting, the underlying issue has not been resolved. Work through the fix steps above.

Full Maytag washer reset guide → Enter diagnostic mode →

Did this guide fix your appliance?

When to Call a Professional

If the hose is clear and F3E1 persists, the pressure sensor or control has failed.

Average professional repair cost for this issue: $150–$300

Related Error Codes

F8E1

Low water fill detected

⚠ Medium Severity

Same Code on Other Brands

Error code F3E1 appears on these other brands too. See every brand that shows F3E1 →

Whirlpool Washing Machine F3E1

Pressure sensor failure — water level sensing fault

Whirlpool Dryer F3E1

Outlet (exhaust) thermistor open or shorted

Whirlpool Dishwasher F3E1

Thermistor failure — low resistance reading

Whirlpool Oven F3-E1

Oven temperature sensor short circuit

Find Replacement Parts

Use these links to find the exact replacement parts for your Maytag Washing Machine:

🔩

Search PartSelect

Maytag Washing Machine repair parts

🔧

Search RepairClinic

Step-by-step video guides

External links — ApplianceErrors.com is not affiliated with these retailers.

More Maytag Washing Machine Error Codes

F9E1 Drain failure — water not draining F1E1 Main electronic control board failure SUD Excessive suds — too much detergent F5E2 Lid will not lock — latch blocked or failed F5E1 Lid lock fault — cannot lock or unlock F5E3 Lid will not unlock — latch or control fault

Frequently Asked Questions

Can I keep using my Maytag Washing Machine when error F3E1 appears? +

You often can for a cycle or two, but the sensor issue behind F3E1 will keep interrupting normal operation until it is fixed. Plan the repair rather than ignoring the code.

What most commonly causes F3E1 on a Maytag Washing Machine? +

Across reported Maytag washing machine repairs, the most frequent is pressure sensor failure (45% of cases), air hose to pressure sensor kinked or clogged (35%), then wiring to sensor fault (20%). Check them in that order before replacing any parts.

F3E1 keeps coming back after a reset — what should I check next? +

A reset only clears the stored F3E1 fault; if it returns, the sensor problem is still present. Move on to the physical checks — check the pressure (air) hose, then power cycle — since the code will reappear until the root cause is resolved. This is a moderate job — a multimeter and some disassembly are usually involved.

How much does it cost to fix Maytag Washing Machine error F3E1? +

A DIY repair typically runs $25–$70 in parts, versus $150–$300 for a professional service call, so handling it yourself saves around $125. Expect the work to take roughly 30–60 minutes.

Which Maytag Washing Machine models show error F3E1? +

F3E1 is documented on Top-load and front-load Maytag washers that use an analog water-level pressure sensor, roughly 2015 onward. Other units sharing the same control platform can display it too, so the fixes here generally transfer across the series.

Sources & References

• Maytag Product Help — official manufacturer documentation
• Our editorial & verification policy

Content verified against manufacturer service documentation. Last verified: July 19, 2026.

← All Maytag Washing Machine Error Codes ← All Maytag Error Codes