Maytag Washing Machine Error Code F1E1

Reviewed by the ApplianceErrors Editorial Team · Verified against manufacturer service documentation · Last verified: June 10, 2026

⚠ High Severity 🔧🔧🔧 Advanced DIY

Main electronic control board failure

The most common cause of the F1E1 error on a Maytag washing machine is main control board component failure (~50% of cases); start with: power cycle the washer.

💰 DIY cost: $100–$300 👨‍🔧 Pro cost: $250–$520 Save $150+ by doing it yourself

Maytag Washing Machine error code F1E1 on the display panel — How the F1E1 code appears on a Maytag washing machine display

What Does Error Code F1E1 Mean on a Maytag Washing Machine?

Main electronic control board failure.

The primary control board failed its internal self-check, so the washer halts and won't run cycles reliably. A failed onboard component (often a relay or capacitor) is the usual root cause, frequently triggered by a power surge or moisture reaching the board.

What Causes Error Code F1E1?

Here are the most common causes in order of frequency. Start with the most likely cause before moving to the next:

1

Main control board component failure 50% of cases
2

Power surge 30% of cases
3

Moisture reaching the board 12% of cases
4

Loose or corroded board connector 8% of cases

How to Fix Maytag Washing Machine Error Code F1E1

🔧🔧🔧 Advanced DIY Est. time: 1–3 hours

⚡ Safety first: Unplug the appliance before opening any panels or touching internal components.

1

Power cycle the washer

Unplug the washer for 15 minutes so the control fully powers down, then restore power and start a cycle to see if F1E1 clears.
2

Reseat the board connectors

Unplug the washer, find the main control board, and reseat any loose or corroded wiring connectors feeding it.

⚠️ Unplug before servicing.
3

Check for moisture

Inspect the board for water spotting or corrosion from a leak or humid laundry room, which can cause intermittent faults.
4

Replace the control board

If F1E1 returns after a power cycle, the main control board has failed and needs replacement.

🔩 Maytag washer control board ($100–$300)

⚠️ Photograph all wiring before disconnecting.

How to Reset Error Code F1E1

Unplug the washer for a full 15 minutes to let the control board discharge, then restore power and start a short cycle. If F1E1 returns immediately, the board has failed and needs replacement.

Note: If the error returns after resetting, the underlying issue has not been resolved. Work through the fix steps above.

Full Maytag washer reset guide → Enter diagnostic mode →

Did this guide fix your appliance?

When to Call a Professional

If a power cycle and connector reseat don't clear F1E1, replacing the main control board is involved work — call a technician, who can also confirm the fault isn't a shorted motor or harness first.

Average professional repair cost for this issue: $250–$520

Related Error Codes

F6E1

Communication error — main control to motor control

⚠ High Severity

Same Code on Other Brands

Error code F1E1 appears on these other brands too. See every brand that shows F1E1 →

Whirlpool Washing Machine F1E1

Main control board failure

Whirlpool Dishwasher F1E1

Control board / thermistor stuck — electronic control fault

Whirlpool Oven F1-E1

EEPROM checksum error — corrupted control memory

Kenmore Dishwasher F1E1

Control board memory error — stuck relay or corrupted firmware

Find Replacement Parts

Use these links to find the exact replacement parts for your Maytag Washing Machine:

🔩

Search PartSelect

Maytag Washing Machine repair parts

🔧

Search RepairClinic

Step-by-step video guides

External links — ApplianceErrors.com is not affiliated with these retailers.

More Maytag Washing Machine Error Codes

F9E1 Drain failure — water not draining F8E1 Low water fill detected SUD Excessive suds — too much detergent F5E2 Lid will not lock — latch blocked or failed F5E1 Lid lock fault — cannot lock or unlock F5E3 Lid will not unlock — latch or control fault

Frequently Asked Questions

Can I keep using my Maytag Washing Machine when error F1E1 appears? +

It is not advisable. The washing machine may still power on, but running it while F1E1 is active can worsen the control-board fault or damage related parts. Treat it as a soon-as-possible repair.

What most commonly causes F1E1 on a Maytag Washing Machine? +

Across reported Maytag washing machine repairs, the most frequent is main control board component failure (50% of cases), power surge (30%), then moisture reaching the board (12%). Check them in that order before replacing any parts.

F1E1 keeps coming back after a reset — what should I check next? +

A reset only clears the stored F1E1 fault; if it returns, the control-board problem is still present. Move on to the physical checks — power cycle the washer, then reseat the board connectors — since the code will reappear until the root cause is resolved. This is an advanced repair involving deeper disassembly or electrical testing.

How much does it cost to fix Maytag Washing Machine error F1E1? +

A DIY repair typically runs $100–$300 in parts, versus $250–$520 for a professional service call, so handling it yourself saves around $150. Expect the work to take 1–3 hours.

Sources & References

• Maytag Product Help — official manufacturer documentation
• Our editorial & verification policy

Content verified against manufacturer service documentation. Last verified: June 10, 2026.

← All Maytag Washing Machine Error Codes ← All Maytag Error Codes