ApplianceErrors.com

Electrolux Washing Machine Error Code E35

Reviewed by the ApplianceErrors Editorial Team · Verified against manufacturer service documentation · Last verified: July 19, 2026
⚠ High Severity 🔧🔧 Moderate DIY

Pressure sensor indicates water overfill

The most common cause of the E35 error on a Electrolux washing machine is inlet valve stuck open (continuous fill) (~45% of cases); start with: shut off the water.

💰 DIY cost: $35–$80 👨‍🔧 Pro cost: $150–$300 Save $115+ by doing it yourself
Electrolux Washing Machine error code E35 on the display panel
How the E35 code appears on a Electrolux washing machine display

What Does Error Code E35 Mean on a Electrolux Washing Machine?

Pressure sensor indicates water overfill.

The control board reads the analog pressure sensor and compares the reported water level against a stored overfill threshold. E35 fires when that reading exceeds the safe maximum, indicating either an actual overfill from an inlet valve that won't seat closed, or a false high signal from a kinked pressure hose, air-trap blockage, or a drifting sensor. Unlike E31 (sensor circuit or calibration fault) or E13 (leak detection), E35 specifically flags a level above maximum rather than a wiring or under-fill condition.

Models affected: Electrolux front-load washers using an analog pressure sensor, including models such as EFLS627UTT and ELFW7637AT
What owners report: Owners commonly report this code mid-cycle, sometimes with visible overfilling and sometimes with a normal-looking tub, which usually points to a misreading sensor or pinched pressure hose. A clogged or crimped pressure hose is a frequent false trigger, and reseating or clearing it is a reported quick win before replacing parts.

What Causes Error Code E35?

Here are the most common causes in order of frequency. Start with the most likely cause before moving to the next:

  1. 1
    Inlet valve stuck open (continuous fill) 45% of cases
  2. 2
    Pressure sensor misreading high 30% of cases
  3. 3
    Pressure hose fault 15% of cases
  4. 4
    Control board fault 10% of cases

How to Fix Electrolux Washing Machine Error Code E35

🔧🔧 Moderate DIY Est. time: 30–60 min
⚡ Safety first: Unplug the appliance before opening any panels or touching internal components.
  1. 1

    Shut off the water

    If the tub is overfilling, close the supply tap immediately.

    ⚠️ Standing water plus electricity is a hazard — unplug the machine.
  2. 2

    Inspect the inlet valve

    A valve that won't fully close will keep filling; test and replace if stuck.

    🔩 Electrolux inlet valve ($35–$75)
  3. 3

    Check the pressure sensor and hose

    If the tub is not actually overfull, the sensor is misreading.

    🔩 Electrolux pressure sensor ($35–$80)

How to Reset Error Code E35

Close the tap and unplug. Do not run the washer until the overfill cause is found.

Note: If the error returns after resetting, the underlying issue has not been resolved. Work through the fix steps above.

Full Electrolux washer reset guide → Enter diagnostic mode → Symptom guide: Washer not filling →

Did this guide fix your appliance?

When to Call a Professional

A washer that keeps overfilling should be serviced promptly to avoid water damage.

Average professional repair cost for this issue: $150–$300

Related Error Codes

E31
Pressure sensor not communicating with the control board
⚠ High Severity
E13
Water leak detected — level dropping when it should not
⚠ High Severity

Find Replacement Parts

Use these links to find the exact replacement parts for your Electrolux Washing Machine:

🔩
Search PartSelect
Electrolux Washing Machine repair parts
🔧
Search RepairClinic
Step-by-step video guides

External links — ApplianceErrors.com is not affiliated with these retailers.

More Electrolux Washing Machine Error Codes

E20 Drain error — water not draining E10 Water inlet error — no water detected E40 Door not closed or door lock failure E50 Motor failure E90 Wiring harness fault — communication error E11 Long fill time — washer not filling during the wash phase

Frequently Asked Questions

Can I keep using my Electrolux Washing Machine when error E35 appears? +
It is not advisable. The washing machine may still power on, but running it while E35 is active can worsen the water-supply fault or damage related parts. Treat it as a soon-as-possible repair.
What most commonly causes E35 on a Electrolux Washing Machine? +
Across reported Electrolux washing machine repairs, the most frequent is inlet valve stuck open (continuous fill) (45% of cases), pressure sensor misreading high (30%), then pressure hose fault (15%). Check them in that order before replacing any parts.
E35 keeps coming back after a reset — what should I check next? +
A reset only clears the stored E35 fault; if it returns, the water-supply problem is still present. Move on to the physical checks — shut off the water, then inspect the inlet valve — since the code will reappear until the root cause is resolved. This is a moderate job — a multimeter and some disassembly are usually involved.
How much does it cost to fix Electrolux Washing Machine error E35? +
A DIY repair typically runs $35–$80 in parts, versus $150–$300 for a professional service call, so handling it yourself saves around $115. Expect the work to take roughly 30–60 minutes.
Which Electrolux Washing Machine models show error E35? +
E35 is documented on Electrolux front-load washers using an analog pressure sensor, including models such as EFLS627UTT and ELFW7637AT. Other units sharing the same control platform can display it too, so the fixes here generally transfer across the series.

Sources & References

Content verified against manufacturer service documentation. Last verified: July 19, 2026.

← All Electrolux Washing Machine Error Codes ← All Electrolux Error Codes