Electrolux Washing Machine Error Code E11

Reviewed by the ApplianceErrors Editorial Team · Verified against manufacturer service documentation · Last verified: July 19, 2026

⚠ Medium Severity 🔧 Easy DIY

Long fill time — washer not filling during the wash phase

The most common cause of the E11 error on a Electrolux washing machine is supply tap partly closed or low pressure (~40% of cases); start with: check the tap and hose.

💰 DIY cost: $0–$75 👨‍🔧 Pro cost: $120–$250 Save $120+ by doing it yourself

Electrolux Washing Machine error code E11 on the display panel — How the E11 code appears on a Electrolux washing machine display

What Does Error Code E11 Mean on a Electrolux Washing Machine?

Long fill time — washer not filling during the wash phase.

E11 fires when the control board does not sense the target water level being reached within the allotted fill window during the main wash phase. The pressure sensor monitors the level and, if it climbs too slowly or not at all, the timeout trips. Unlike E13 (a leak or drain-related fault) or the closely related E10 family, E11 points specifically to slow or absent fill during wash — most often a restricted supply, blocked inlet screen, or a weak inlet valve solenoid.

Models affected: Electrolux front-load washers, including models such as EFLS627UTT and ELFW7637AT

What owners report: Owners commonly report E11 appearing early in a cycle, often after a hose was kinked behind the machine or a supply tap was left only partly open. A frequent quick win is simply opening the tap fully and cleaning the mesh inlet screen, which can clear the code without any parts.

What Causes Error Code E11?

Here are the most common causes in order of frequency. Start with the most likely cause before moving to the next:

1

Supply tap partly closed or low pressure 40% of cases
2

Inlet screen/hose blocked or kinked 30% of cases
3

Inlet valve solenoid weak 20% of cases
4

Pressure sensor reading low 10% of cases

How to Fix Electrolux Washing Machine Error Code E11

🔧 Easy DIY Est. time: 10–20 min

⚡ Safety first: Unplug the appliance before opening any panels or touching internal components.

1

Check the tap and hose

Open the supply tap fully and straighten the fill hose. Confirm reasonable household water pressure.
2

Clean the inlet screen

Close the tap, remove the fill hose, and clean the mesh screen at the washer inlet.
3

Test the inlet valve

Test the solenoid for continuity and replace if open.

🔩 Electrolux inlet valve ($35–$75)

How to Reset Error Code E11

Open the tap fully and press Start/Pause to resume. If E11 returns early in fill, clean the inlet screen and retest.

Note: If the error returns after resetting, the underlying issue has not been resolved. Work through the fix steps above.

Full Electrolux washer reset guide → Enter diagnostic mode → Symptom guide: Washer not filling →

Did this guide fix your appliance?

When to Call a Professional

If supply and valve are confirmed good and E11 persists, the pressure sensor or control board needs testing.

Average professional repair cost for this issue: $120–$250

Related Error Codes

E10

Water inlet error — no water detected

⚠ Medium Severity

E13

Water leak detected — level dropping when it should not

⚠ High Severity

Same Code on Other Brands

Error code E11 appears on these other brands too. See every brand that shows E11 →

Frigidaire Washing Machine E11

Fill time exceeded — water not filling

Frigidaire Dryer E11

Control board failure

Find Replacement Parts

Use these links to find the exact replacement parts for your Electrolux Washing Machine:

🔩

Search PartSelect

Electrolux Washing Machine repair parts

🔧

Search RepairClinic

Step-by-step video guides

External links — ApplianceErrors.com is not affiliated with these retailers.

More Electrolux Washing Machine Error Codes

E20 Drain error — water not draining E40 Door not closed or door lock failure E50 Motor failure E90 Wiring harness fault — communication error E21 Drain error — water not pumping out fast enough E23 Drain pump triac/relay failure on the control board

Frequently Asked Questions

Can I keep using my Electrolux Washing Machine when error E11 appears? +

You often can for a cycle or two, but the water-supply issue behind E11 will keep interrupting normal operation until it is fixed. Plan the repair rather than ignoring the code.

What most commonly causes E11 on a Electrolux Washing Machine? +

Across reported Electrolux washing machine repairs, the most frequent is supply tap partly closed or low pressure (40% of cases), inlet screen/hose blocked or kinked (30%), then inlet valve solenoid weak (20%). Check them in that order before replacing any parts.

E11 keeps coming back after a reset — what should I check next? +

A reset only clears the stored E11 fault; if it returns, the water-supply problem is still present. Move on to the physical checks — check the tap and hose, then clean the inlet screen — since the code will reappear until the root cause is resolved. This is a beginner-friendly job needing only basic hand tools.

How much does it cost to fix Electrolux Washing Machine error E11? +

A DIY repair typically runs $0–$75 in parts, versus $120–$250 for a professional service call, so handling it yourself saves around $120. Expect the work to take about 10–20 minutes.

Which Electrolux Washing Machine models show error E11? +

E11 is documented on Electrolux front-load washers, including models such as EFLS627UTT and ELFW7637AT. Other units sharing the same control platform can display it too, so the fixes here generally transfer across the series.

Sources & References

• Electrolux Support — official manufacturer documentation
• Our editorial & verification policy

Content verified against manufacturer service documentation. Last verified: July 19, 2026.

← All Electrolux Washing Machine Error Codes ← All Electrolux Error Codes