ApplianceErrors.com

Whirlpool Oven Error Code F1-E3

Reviewed by the ApplianceErrors Editorial Team · Verified against manufacturer service documentation · Last verified: July 19, 2026
⚠ Medium Severity 🔧🔧 Moderate DIY

Wiring harness / cavity size mismatch

The most common cause of the F1-E3 error on a Whirlpool oven is replacement control board not configured for this model/cavity (~45% of cases); start with: reset power.

💰 DIY cost: $150–$380 👨‍🔧 Pro cost: $200–$500
Whirlpool Oven error code F1-E3 on the display panel
How the F1-E3 code appears on a Whirlpool oven display

What Does Error Code F1-E3 Mean on a Whirlpool Oven?

Wiring harness / cavity size mismatch.

F1-E3 fires when the control compares the cavity-size configuration it reads from the model jumper or wiring harness against the value stored in its onboard memory and finds a mismatch. Unlike F1-E4 (a related configuration or memory error) or a generic F1, this code points specifically at a harness/jumper reading the board doesn't recognize. It most often follows a control board swap with an unconfigured or wrong part, or a damaged, disconnected configuration harness.

Models affected: Whirlpool electric and gas ranges/ovens using the F1-E series fault reporting, including models such as WFE525S0JZ and WFG320M0BS
What owners report: Owners commonly report this code appearing right after a control board replacement, since the new board may not be configured for the oven's cavity size. A simple 5-minute power cycle sometimes clears a one-time glitch, but if it returns after a board swap, the wrong or unconfigured part is the usual culprit.

What Causes Error Code F1-E3?

Here are the most common causes in order of frequency. Start with the most likely cause before moving to the next:

  1. 1
    Replacement control board not configured for this model/cavity 45% of cases
  2. 2
    Configuration harness/jumper damaged or disconnected 35% of cases
  3. 3
    Control board memory fault 20% of cases

How to Fix Whirlpool Oven Error Code F1-E3

🔧🔧 Moderate DIY Est. time: 30–60 min
⚡ Safety first: Unplug the appliance before opening any panels or touching internal components.
  1. 1

    Reset power

    Turn off the circuit breaker for 5 minutes, then restore power and retest.

  2. 2

    Check the configuration harness

    Verify the model/cavity-size jumper or configuration harness is connected and undamaged.

    ⚠️ Unplug oven before servicing.
  3. 3

    Use the correct control board

    If a board was just replaced, confirm it is the correct part configured for this oven's cavity size.

    🔩 Whirlpool oven control board ($150–$380)
    ⚠️ Unplug oven before servicing.

How to Reset Error Code F1-E3

Power cycle 5 minutes and confirm the configuration harness is connected. If F1-E3 followed a board swap, fit the correct configured board.

Note: If the error returns after resetting, the underlying issue has not been resolved. Work through the fix steps above.

Full Whirlpool oven reset guide → Enter diagnostic mode →

Did this guide fix your appliance?

When to Call a Professional

If the configuration harness is sound and the board is the correct part but F1-E3 persists, the control board has failed.

Average professional repair cost for this issue: $200–$500

Related Error Codes

F1-E4
Model ID error — control not configured for this model
⚠ Medium Severity
F1
Control board failure
⚠ High Severity

Find Replacement Parts

Use these links to find the exact replacement parts for your Whirlpool Oven:

🔩
Search PartSelect
Whirlpool Oven repair parts
🔧
Search RepairClinic
Step-by-step video guides

External links — ApplianceErrors.com is not affiliated with these retailers.

More Whirlpool Oven Error Codes

F2-E0 Shorted keypad — stuck key on control panel F2-E1 Keypad/touchpad disconnected from control board F3-E0 Oven temperature sensor open circuit F3-E1 Oven temperature sensor short circuit F3-E2 Oven over-temperature — temp exceeded safe limit F5-E0 Door switch failure — latch not sensing door position

Frequently Asked Questions

Can I keep using my Whirlpool Oven when error F1-E3 appears? +
You often can for a cycle or two, but the control-board issue behind F1-E3 will keep interrupting normal operation until it is fixed. Plan the repair rather than ignoring the code.
What most commonly causes F1-E3 on a Whirlpool Oven? +
Across reported Whirlpool oven repairs, the most frequent is replacement control board not configured for this model/cavity (45% of cases), configuration harness/jumper damaged or disconnected (35%), then control board memory fault (20%). Check them in that order before replacing any parts.
F1-E3 keeps coming back after a reset — what should I check next? +
A reset only clears the stored F1-E3 fault; if it returns, the control-board problem is still present. Move on to the physical checks — reset power, then check the configuration harness — since the code will reappear until the root cause is resolved. This is a moderate job — a multimeter and some disassembly are usually involved.
How much does it cost to fix Whirlpool Oven error F1-E3? +
A DIY repair typically runs $150–$380 in parts, versus $200–$500 for a professional service call. Expect the work to take roughly 30–60 minutes.
Which Whirlpool Oven models show error F1-E3? +
F1-E3 is documented on Whirlpool electric and gas ranges/ovens using the F1-E series fault reporting, including models such as WFE525S0JZ and WFG320M0BS. Other units sharing the same control platform can display it too, so the fixes here generally transfer across the series.

Sources & References

Content verified against manufacturer service documentation. Last verified: July 19, 2026.

← All Whirlpool Oven Error Codes ← All Whirlpool Error Codes