ApplianceErrors.com

Maytag Oven Error Code F0

Reviewed by the ApplianceErrors Editorial Team · Verified against manufacturer service documentation · Last verified: July 19, 2026
⚠ High Severity 🔧🔧🔧 Advanced DIY Also shown as: F00

Electronic Range Control (ERC) failure — failed transistor/control board

The most common cause of the F0 error on a Maytag oven is failed transistor/relay-drive on the ERC board (~55% of cases); start with: power cycle the range.

💰 DIY cost: $120–$300 👨‍🔧 Pro cost: $250–$500 Save $130+ by doing it yourself
Maytag Oven error code F0 on the display panel
How the F0 code appears on a Maytag oven display

What Does Error Code F0 Mean on a Maytag Oven?

Electronic Range Control (ERC) failure — failed transistor/control board.

F0 (also shown as F00) is the control board's self-diagnostic flagging an internal Electronic Range Control fault, most often a failed output transistor or relay-drive circuit that can no longer switch the oven's heating loads reliably. Unlike F1 codes, which point to a stuck key or watchdog/keypad fault, F0 signals hardware failure on the board itself. Power surges and simple age commonly trigger it. Because the drive circuitry is compromised, the ERC cannot control oven operation safely.

Models affected: Older Maytag MER/MGR single-digit-code electric and gas ranges with an ERC board
What owners report: Owners commonly report F0 appearing suddenly, sometimes after a storm or power flicker, occasionally with a beep. A breaker power cycle for 10–15 minutes clears it now and then, but many find the code returns, which usually points to board replacement rather than a quick fix.

What Causes Error Code F0?

Here are the most common causes in order of frequency. Start with the most likely cause before moving to the next:

  1. 1
    Failed transistor/relay-drive on the ERC board 55% of cases
  2. 2
    Power surge damaging the control board 30% of cases
  3. 3
    ERC board age-related failure 15% of cases

How to Fix Maytag Oven Error Code F0

🔧🔧🔧 Advanced DIY Est. time: 1–3 hours
⚡ Safety first: Unplug the appliance before opening any panels or touching internal components.
  1. 1

    Power cycle the range

    Turn off the circuit breaker for 5–15 minutes. A power cycle occasionally clears a transient F0.

  2. 2

    Replace the ERC control board

    F0 is almost always a board failure. The board is behind the control panel; disconnect all harnesses after photographing them.

    🔩 Maytag oven ERC control board ($120–$300)
    ⚠️ Photograph all wiring harness positions before disconnecting.

How to Reset Error Code F0

Turn off the breaker for 15 minutes. If F0 returns, the ERC control board must be replaced.

Note: If the error returns after resetting, the underlying issue has not been resolved. Work through the fix steps above.

Did this guide fix your appliance?

When to Call a Professional

Control board replacement involves high-voltage connections; professional installation is recommended.

Average professional repair cost for this issue: $250–$500

Related Error Codes

F1
ERC control board failure / clock fault — watchdog reset
⚠ High Severity
F1-E0
ERC board EEPROM checksum error — control board memory failure
⚠ High Severity

Same Code on Other Brands

Error code F0 appears on these other brands too. See every brand that shows F0 →

Whirlpool logo
Whirlpool Oven F0
Control board failure
GE Appliances logo
GE Appliances Oven F0
Keypad stuck — a button is continuously pressed

Find Replacement Parts

Use these links to find the exact replacement parts for your Maytag Oven:

🔩
Search PartSelect
Maytag Oven repair parts
🔧
Search RepairClinic
Step-by-step video guides

External links — ApplianceErrors.com is not affiliated with these retailers.

More Maytag Oven Error Codes

F1-E1 ERC board keypad stuck key — shorted keypad detected during power-up F2-E0 Shorted keypad — stuck key during normal operation F2-E1 Keypad disconnected — ribbon cable failure F3-E0 Oven temperature sensor open circuit F3-E1 Oven temperature sensor short circuit F3-E2 Oven over-temperature — exceeded safe operating limit

Frequently Asked Questions

Can I keep using my Maytag Oven when error F0 appears? +
It is not advisable. The oven may still power on, but running it while F0 is active can worsen the control-board fault or damage related parts. Treat it as a soon-as-possible repair.
What most commonly causes F0 on a Maytag Oven? +
Across reported Maytag oven repairs, the most frequent is failed transistor/relay-drive on the ERC board (55% of cases), power surge damaging the control board (30%), then eRC board age-related failure (15%). Check them in that order before replacing any parts.
F0 keeps coming back after a reset — what should I check next? +
A reset only clears the stored F0 fault; if it returns, the control-board problem is still present. Move on to the physical checks — power cycle the range, then replace the ERC control board — since the code will reappear until the root cause is resolved. This is an advanced repair involving deeper disassembly or electrical testing.
How much does it cost to fix Maytag Oven error F0? +
A DIY repair typically runs $120–$300 in parts, versus $250–$500 for a professional service call, so handling it yourself saves around $130. Expect the work to take 1–3 hours.
Which Maytag Oven models show error F0? +
F0 is documented on Older Maytag MER/MGR single-digit-code electric and gas ranges with an ERC board. Other units sharing the same control platform can display it too, so the fixes here generally transfer across the series.

Sources & References

Content verified against manufacturer service documentation. Last verified: July 19, 2026.

← All Maytag Oven Error Codes ← All Maytag Error Codes