ApplianceErrors.com

Electrolux Washing Machine Error Code E52

Reviewed by the ApplianceErrors Editorial Team · Verified against manufacturer service documentation · Last verified: July 19, 2026
⚠ High Severity 🔧🔧🔧 Advanced DIY

No signal from the motor tacho generator

The most common cause of the E52 error on a Electrolux washing machine is tacho coil/sensor faulty (~45% of cases); start with: check the motor connector.

💰 DIY cost: $15–$260 👨‍🔧 Pro cost: $200–$450 Save $185+ by doing it yourself
Electrolux Washing Machine error code E52 on the display panel
How the E52 code appears on a Electrolux washing machine display

What Does Error Code E52 Mean on a Electrolux Washing Machine?

No signal from the motor tacho generator.

E52 fires when the control board sends drive commands but reads no valid pulse train from the motor's tachometer generator, leaving it blind to actual drum RPM. Without this feedback the board cannot ramp or hold speed safely, so it halts the cycle. It stems from an open or shorted tacho coil, a loose motor connector, or worn brushes interrupting the signal. This differs from E51 and E53, which point to triac or motor overcurrent faults rather than a missing speed reading.

Models affected: Electrolux front-load washers with a tachometer-equipped drive motor; the fault applies across the line including models such as EFLS627UTT and ELFW7637AT.
What owners report: Owners commonly report E52 appearing at the transition into spin or when the drum tries to accelerate, often mid-cycle. A loose or corroded motor connector is a frequent easy fix, so reseating it before ordering parts is worth trying. On older brushed motors, erratic behavior sometimes traces back to worn carbon brushes rather than the motor itself.

What Causes Error Code E52?

Here are the most common causes in order of frequency. Start with the most likely cause before moving to the next:

  1. 1
    Tacho coil/sensor faulty 45% of cases
  2. 2
    Wiring/connector to motor loose 30% of cases
  3. 3
    Carbon brushes worn (brushed motors) 15% of cases
  4. 4
    Control board fault 10% of cases

How to Fix Electrolux Washing Machine Error Code E52

🔧🔧🔧 Advanced DIY Est. time: 1–3 hours
⚡ Safety first: Unplug the appliance before opening any panels or touching internal components.
  1. 1

    Check the motor connector

    Reseat the wiring connector at the motor and the control board.

    ⚠️ Unplug before inspecting.
  2. 2

    Inspect motor brushes

    On brushed motors, worn carbon brushes cause erratic or no tacho signal.

    🔩 Electrolux motor carbon brushes ($15–$35)
  3. 3

    Test/replace the tacho or motor

    If the tacho coil is open, the motor usually needs replacement.

    🔩 Electrolux drive motor ($120–$260)

How to Reset Error Code E52

Unplug 10 minutes. If E52 returns, inspect the motor connector and brushes.

Note: If the error returns after resetting, the underlying issue has not been resolved. Work through the fix steps above.

Full Electrolux washer reset guide → Enter diagnostic mode → Symptom guide: Washer not spinning →

Did this guide fix your appliance?

When to Call a Professional

If wiring, brushes, and tacho are good, the control board speed input has failed.

Average professional repair cost for this issue: $200–$450

Related Error Codes

E51
Drive motor triac short-circuit on the control board
⚠ High Severity
E53
Motor control circuit fault — low voltage to the speed control
⚠ High Severity

Same Code on Other Brands

Error code E52 appears on these other brands too. See every brand that shows E52 →

GE Appliances logo
GE Appliances Washing Machine E52
Spin speed error — motor not reaching target RPM
Frigidaire logo
Frigidaire Washing Machine E52
Bad signal from the motor tachogenerator

Find Replacement Parts

Use these links to find the exact replacement parts for your Electrolux Washing Machine:

🔩
Search PartSelect
Electrolux Washing Machine repair parts
🔧
Search RepairClinic
Step-by-step video guides

External links — ApplianceErrors.com is not affiliated with these retailers.

More Electrolux Washing Machine Error Codes

E20 Drain error — water not draining E10 Water inlet error — no water detected E40 Door not closed or door lock failure E50 Motor failure E90 Wiring harness fault — communication error E11 Long fill time — washer not filling during the wash phase

Frequently Asked Questions

Can I keep using my Electrolux Washing Machine when error E52 appears? +
It is not advisable. The washing machine may still power on, but running it while E52 is active can worsen the motor fault or damage related parts. Treat it as a soon-as-possible repair.
What most commonly causes E52 on a Electrolux Washing Machine? +
Across reported Electrolux washing machine repairs, the most frequent is tacho coil/sensor faulty (45% of cases), wiring/connector to motor loose (30%), then carbon brushes worn (brushed motors) (15%). Check them in that order before replacing any parts.
E52 keeps coming back after a reset — what should I check next? +
A reset only clears the stored E52 fault; if it returns, the motor problem is still present. Move on to the physical checks — check the motor connector, then inspect motor brushes — since the code will reappear until the root cause is resolved. This is an advanced repair involving deeper disassembly or electrical testing.
How much does it cost to fix Electrolux Washing Machine error E52? +
A DIY repair typically runs $15–$260 in parts, versus $200–$450 for a professional service call, so handling it yourself saves around $185. Expect the work to take 1–3 hours.
Which Electrolux Washing Machine models show error E52? +
E52 is documented on Electrolux front-load washers with a tachometer-equipped drive motor; the fault applies across the line including models such as EFLS627UTT and ELFW7637AT.. Other units sharing the same control platform can display it too, so the fixes here generally transfer across the series.

Sources & References

Content verified against manufacturer service documentation. Last verified: July 19, 2026.

← All Electrolux Washing Machine Error Codes ← All Electrolux Error Codes