ApplianceErrors.com

Frigidaire Washing Machine Error Code E47

Reviewed by the ApplianceErrors Editorial Team · Verified against manufacturer service documentation · Last verified: July 19, 2026
⚠ Medium Severity 🔧🔧 Moderate DIY

Door lock PTC circuit reads open during spin

The most common cause of the E47 error on a Frigidaire washing machine is door lock assembly (PTC) failed (~55% of cases); start with: power reset.

💰 DIY cost: $40–$100 👨‍🔧 Pro cost: $150–$320 Save $110+ by doing it yourself
Frigidaire Washing Machine error code E47 on the display panel
How the E47 code appears on a Frigidaire washing machine display

What Does Error Code E47 Mean on a Frigidaire Washing Machine?

Door lock PTC circuit reads open during spin.

E47 fires when the control monitors the door-lock PTC heater circuit during spin and reads it as open, meaning it cannot verify the door is mechanically locked. Rather than allow the drum to accelerate with an unconfirmed lock, the control halts the cycle for safety. This differs from E41/E42, which point to the lock not engaging or a general door-open condition; E47 specifically flags an open PTC circuit detected mid-spin, usually a failed lock or broken harness connection.

Models affected: Front-load Frigidaire washers with an electronic door-lock (PTC) assembly and fault-code display, roughly the mid-2000s onward
What owners report: Owners commonly report E47 appearing partway through a cycle just as the machine tries to ramp up to spin, sometimes with the door still latching normally. A power reset occasionally clears a one-off glitch, but repeat trips usually point to a worn lock assembly or a chafed harness wire near the door hinge area.

What Causes Error Code E47?

Here are the most common causes in order of frequency. Start with the most likely cause before moving to the next:

  1. 1
    Door lock assembly (PTC) failed 55% of cases
  2. 2
    Wiring/connector to the door lock open 30% of cases
  3. 3
    Control board door-lock circuit fault 15% of cases

How to Fix Frigidaire Washing Machine Error Code E47

🔧🔧 Moderate DIY Est. time: 30–60 min
⚡ Safety first: Unplug the appliance before opening any panels or touching internal components.
  1. 1

    Power reset

    Unplug for 2 minutes and restart a spin to see if E47 clears.

  2. 2

    Check the lock wiring

    Inspect the harness between the door lock and the control board for an open connection.

    ⚠️ Unplug the washer first.
  3. 3

    Replace the door lock assembly

    If wiring is good, the PTC lock has failed.

    🔩 Frigidaire door lock assembly ($40–$100)

How to Reset Error Code E47

Unplug 2 minutes and restart. If E47 returns during spin, service the door lock circuit.

Note: If the error returns after resetting, the underlying issue has not been resolved. Work through the fix steps above.

Symptom guide: Washer won't start →

Did this guide fix your appliance?

When to Call a Professional

If the door lock and wiring test good, the control board door-lock circuit has failed.

Average professional repair cost for this issue: $150–$320

Related Error Codes

E41
Door open — lid or door not properly closed
⚠ Medium Severity
E42
Door will not unlock at the end of the cycle
⚠ Medium Severity

Same Code on Other Brands

Error code E47 appears on these other brands too. See every brand that shows E47 →

GE Appliances logo
GE Appliances Washing Machine E47
Door lock failure

Find Replacement Parts

Use these links to find the exact replacement parts for your Frigidaire Washing Machine:

🔩
Search PartSelect
Frigidaire Washing Machine repair parts
🔧
Search RepairClinic
Step-by-step video guides

External links — ApplianceErrors.com is not affiliated with these retailers.

More Frigidaire Washing Machine Error Codes

E21 Drain time exceeded — water not draining E11 Fill time exceeded — water not filling E45 Door lock control board failure E13 Water leak in tub or air leak in the pressure-sensor air bell E23 Drain pump relay failure on the control board E43 Control board communications fault

Frequently Asked Questions

Can I keep using my Frigidaire Washing Machine when error E47 appears? +
You often can for a cycle or two, but the door issue behind E47 will keep interrupting normal operation until it is fixed. Plan the repair rather than ignoring the code.
What most commonly causes E47 on a Frigidaire Washing Machine? +
Across reported Frigidaire washing machine repairs, the most frequent is door lock assembly (PTC) failed (55% of cases), wiring/connector to the door lock open (30%), then control board door-lock circuit fault (15%). Check them in that order before replacing any parts.
E47 keeps coming back after a reset — what should I check next? +
A reset only clears the stored E47 fault; if it returns, the door problem is still present. Move on to the physical checks — power reset, then check the lock wiring — since the code will reappear until the root cause is resolved. This is a moderate job — a multimeter and some disassembly are usually involved.
How much does it cost to fix Frigidaire Washing Machine error E47? +
A DIY repair typically runs $40–$100 in parts, versus $150–$320 for a professional service call, so handling it yourself saves around $110. Expect the work to take roughly 30–60 minutes.
Which Frigidaire Washing Machine models show error E47? +
E47 is documented on Front-load Frigidaire washers with an electronic door-lock (PTC) assembly and fault-code display, roughly the mid-2000s onward. Other units sharing the same control platform can display it too, so the fixes here generally transfer across the series.

Sources & References

Content verified against manufacturer service documentation. Last verified: July 19, 2026.

← All Frigidaire Washing Machine Error Codes ← All Frigidaire Error Codes