ApplianceErrors.com

Samsung Oven Error Code E-08

Reviewed by the ApplianceErrors Editorial Team · Verified against manufacturer service documentation · Last verified: June 10, 2026
⚠ High Severity 🔧 Easy DIY

Oven temperature sensor open circuit

The most common cause of the E-08 error on a Samsung oven is temperature sensor failure (open circuit) (~65% of cases); start with: test the sensor.

💰 DIY cost: $25–$55 👨‍🔧 Pro cost: $150–$280 Save $125+ by doing it yourself
Samsung Oven error code E-08 on the display panel
How the E-08 code appears on a Samsung oven display

What Does Error Code E-08 Mean on a Samsung Oven?

Oven temperature sensor open circuit.

E-08 fires when the control board reads an open circuit on the oven's NTC temperature probe — resistance measures effectively infinite instead of the expected ~1,080 ohms at room temperature. Without a valid sensor signal the board cannot regulate cavity heat safely, so it locks out heating. This differs from E-09, which typically indicates a shorted sensor (resistance too low) rather than a broken or disconnected one. A loose or corroded 2-pin connector can mimic the same open reading.

Models affected: Samsung NE/NX series gas and electric ranges, including models such as NE59M4320SS, NX58R5601SS, and NE63A6511SS
What owners report: Owners commonly report E-08 appearing at power-on or partway into a bake cycle, with the oven refusing to heat. Before buying parts, many find that simply reseating the sensor connector at the upper-rear of the cavity clears a false trigger caused by corrosion or a loose pin.

What Causes Error Code E-08?

Here are the most common causes in order of frequency. Start with the most likely cause before moving to the next:

  1. 1
    Temperature sensor failure (open circuit) 65% of cases
  2. 2
    Connector at sensor loose or corroded 25% of cases
  3. 3
    Wiring harness to sensor damaged 10% of cases

How to Fix Samsung Oven Error Code E-08

🔧 Easy DIY Est. time: 10–20 min
⚡ Safety first: Unplug the appliance before opening any panels or touching internal components.
  1. 1

    Test the sensor

    Disconnect the sensor connector. Test resistance: at room temperature, expect 1,080–1,090 ohms for a standard oven sensor. An open circuit (OL/∞) means the sensor has failed.

    🔩 Multimeter
  2. 2

    Check the connector

    Before replacing, reseat the 2-pin connector at the sensor. Corrosion on the pins can mimic an open circuit.

  3. 3

    Replace the temperature sensor

    The sensor is in the upper-rear of the oven cavity, usually 1–2 screws. Disconnect the 2-wire connector and install the new sensor.

    🔩 Samsung oven temperature sensor ($25–$55)
    ⚠️ Let oven cool completely before reaching inside.

How to Reset Error Code E-08

After replacing sensor, plug in and test with a short bake cycle.

Note: If the error returns after resetting, the underlying issue has not been resolved. Work through the fix steps above.

Full Samsung oven reset guide → Enter diagnostic mode →

Did this guide fix your appliance?

When to Call a Professional

If new sensor and E-08 persists, the control board sensor input has failed.

Average professional repair cost for this issue: $150–$280

Related Error Codes

E-09
Oven temperature sensor short circuit
⚠ High Severity

Find Replacement Parts

Use these links to find the exact replacement parts for your Samsung Oven:

🔩
Search PartSelect
Samsung Oven repair parts
🔧
Search RepairClinic
Step-by-step video guides

External links — ApplianceErrors.com is not affiliated with these retailers.

More Samsung Oven Error Codes

SE Keypad/touchpad short — stuck button on control panel E-0A Oven overheating — temperature above safe limit NF No flame detected — gas ignition failure (gas range models) E-3 Door lock motor failure — self-clean door latch issue E-43 Power relay failure on main control board C-D0 Button/key problem — a key is registering as pressed

Frequently Asked Questions

Can I keep using my Samsung Oven when error E-08 appears? +
It is not advisable. The oven may still power on, but running it while E-08 is active can worsen the sensor fault or damage related parts. Treat it as a soon-as-possible repair.
What most commonly causes E-08 on a Samsung Oven? +
Across reported Samsung oven repairs, the most frequent is temperature sensor failure (open circuit) (65% of cases), connector at sensor loose or corroded (25%), then wiring harness to sensor damaged (10%). Check them in that order before replacing any parts.
E-08 keeps coming back after a reset — what should I check next? +
A reset only clears the stored E-08 fault; if it returns, the sensor problem is still present. Move on to the physical checks — test the sensor, then check the connector — since the code will reappear until the root cause is resolved. This is a beginner-friendly job needing only basic hand tools.
How much does it cost to fix Samsung Oven error E-08? +
A DIY repair typically runs $25–$55 in parts, versus $150–$280 for a professional service call, so handling it yourself saves around $125. Expect the work to take about 10–20 minutes.
Which Samsung Oven models show error E-08? +
E-08 is documented on Samsung NE/NX series gas and electric ranges, including models such as NE59M4320SS, NX58R5601SS, and NE63A6511SS. Other units sharing the same control platform can display it too, so the fixes here generally transfer across the series.

Sources & References

Content verified against manufacturer service documentation. Last verified: June 10, 2026.

← All Samsung Oven Error Codes ← All Samsung Error Codes