Kenmore Oven Error Code F10

Reviewed by the ApplianceErrors Editorial Team · Verified against manufacturer service documentation · Last verified: June 11, 2026

🛑 Critical — Stop Using 🔧🔧 Moderate DIY

Runaway temperature detected

The most common cause of the F10 error on a Kenmore oven is drifted/shorted oven temperature sensor (~50% of cases); start with: kill power immediately.

💰 DIY cost: $20–$280 👨‍🔧 Pro cost: $220–$450 Save $200+ by doing it yourself

Kenmore Oven error code F10 on the display panel — How the F10 code appears on a Kenmore oven display

What Does Error Code F10 Mean on a Kenmore Oven?

Runaway temperature detected.

F10 fires when the electronic oven control reads a temperature climbing past the commanded setpoint — or rising when no heat was requested. The control watches the sensor's resistance; a shorted or drifted sensor sends an artificially low reading, so the board keeps the element energized. Alternatively, a welded relay leaves the element powered regardless of logic. Unlike F2 (over-temp shutdown) or F1 (control fault), F10 signals genuine thermal runaway, the platform's most safety-critical fault.

Models affected: Kenmore 790 Series ranges and ovens on the Frigidaire electronic-control platform

What owners report: Owners commonly report F10 appearing mid-bake or, alarmingly, while the oven sits idle and warms on its own. A drifted sensor is a frequent culprit and swapping it often clears the code, but if the element stays hot with the oven off, that usually points to a welded relay and the board — either way, kill the breaker first.

What Causes Error Code F10?

Here are the most common causes in order of frequency. Start with the most likely cause before moving to the next:

1

Drifted/shorted oven temperature sensor 50% of cases
2

Welded relay on the control board 35% of cases
3

Failed electronic oven control logic 15% of cases

How to Fix Kenmore Oven Error Code F10

🔧🔧 Moderate DIY Est. time: 30–60 min

⚡ Safety first: Unplug the appliance before opening any panels or touching internal components.

1

Kill power immediately

If the oven is heating uncommanded, switch off the breaker now and leave it off.

⚠️ Do not use the oven until repaired — uncommanded heating is a fire hazard.
2

Test the temperature sensor

Breaker off; measure the sensor (~1080–1100 ohms at room temp) and replace if out of spec.

🔩 Kenmore oven temperature sensor ($20–$50)
3

Replace the control board

If the sensor is in spec, the relay board/EOC has failed and must be replaced before the oven is used again.

🔩 Kenmore electronic oven control ($120–$280)

⚠️ Mains voltage at the board — breaker off, verify dead.

How to Reset Error Code F10

Do not simply reset and resume — repair first, then restore the breaker and verify with an oven thermometer.

Note: If the error returns after resetting, the underlying issue has not been resolved. Work through the fix steps above.

Did this guide fix your appliance?

When to Call a Professional

Treat F10 as a call-a-pro code unless you can confidently test the sensor and verify the relay — the failure mode is dangerous.

Average professional repair cost for this issue: $220–$450

Related Error Codes

Electronic oven control (EOC) fault — runaway or internal failure

⚠ High Severity

Oven over-temperature detected

⚠ High Severity

Same Code on Other Brands

Error code F10 appears on these other brands too. See every brand that shows F10 →

Samsung Microwave F-10

Thermistor shorted — over-temperature protection

Frigidaire Oven F10

Runaway temperature — oven overheating

Electrolux Oven F10

Runaway temperature detected

Miele Oven F10

Water intake fault (steam/combi models)

Find Replacement Parts

Use these links to find the exact replacement parts for your Kenmore Oven:

🔩

Search PartSelect

Kenmore Oven repair parts

🔧

Search RepairClinic

Step-by-step video guides

External links — ApplianceErrors.com is not affiliated with these retailers.

More Kenmore Oven Error Codes

F3 Oven temperature sensor open circuit F4 Oven temperature sensor shorted F31 Oven temperature sensor shorted (Frigidaire-platform models)

Frequently Asked Questions

Can I keep using my Kenmore Oven when error F10 appears? +

No — stop using the oven right away. F10 is a critical temperature fault, and continuing to run it risks further damage or a safety hazard. Unplug it and resolve the fault before the next cycle.

What most commonly causes F10 on a Kenmore Oven? +

Across reported Kenmore oven repairs, the most frequent is drifted/shorted oven temperature sensor (50% of cases), welded relay on the control board (35%), then failed electronic oven control logic (15%). Check them in that order before replacing any parts.

F10 keeps coming back after a reset — what should I check next? +

A reset only clears the stored F10 fault; if it returns, the temperature problem is still present. Move on to the physical checks — kill power immediately, then test the temperature sensor — since the code will reappear until the root cause is resolved. This is a moderate job — a multimeter and some disassembly are usually involved.

How much does it cost to fix Kenmore Oven error F10? +

A DIY repair typically runs $20–$280 in parts, versus $220–$450 for a professional service call, so handling it yourself saves around $200. Expect the work to take roughly 30–60 minutes.

Which Kenmore Oven models show error F10? +

F10 is documented on Kenmore 790 Series ranges and ovens on the Frigidaire electronic-control platform. Other units sharing the same control platform can display it too, so the fixes here generally transfer across the series.

Sources & References

• Kenmore Customer Care — official manufacturer documentation
• Our editorial & verification policy

Content verified against manufacturer service documentation. Last verified: June 11, 2026.

← All Kenmore Oven Error Codes ← All Kenmore Error Codes