ApplianceErrors.com

Electrolux Oven Error Code F13

Reviewed by the ApplianceErrors Editorial Team · Verified against manufacturer service documentation · Last verified: June 11, 2026
⚠ Medium Severity 🔧🔧🔧 Advanced DIY

Control board internal checksum/EEPROM error

The most common cause of the F13 error on a Electrolux oven is corrupted EEPROM data after a power surge (~45% of cases); start with: hard reset.

💰 DIY cost: $0–$300 👨‍🔧 Pro cost: $220–$420 Save $220+ by doing it yourself
Electrolux Oven error code F13 on the display panel
How the F13 code appears on a Electrolux oven display

What Does Error Code F13 Mean on a Electrolux Oven?

Control board internal checksum/EEPROM error.

F13 fires when the oven control runs its power-on memory self-check and the stored EEPROM data fails the checksum comparison — calibration, program, or configuration values read back corrupted. The board cannot trust its own settings, so it faults out. Unlike F10 (runaway/over-temperature from the sensor circuit) or F14 (EEPROM read/write hardware fault), F13 specifically flags corrupted stored data, which a full power-down sometimes clears by reloading defaults before the board itself is condemned.

Models affected: Electrolux wall ovens and electric ranges with an electronic oven control (EOC), broadly across models using digital control boards
What owners report: Owners commonly report F13 appearing suddenly after a storm, brownout, or breaker trip, and many find a 10-minute power-down at the breaker clears it at least temporarily. If it keeps returning after a full reset, owners generally end up replacing the control board.

What Causes Error Code F13?

Here are the most common causes in order of frequency. Start with the most likely cause before moving to the next:

  1. 1
    Corrupted EEPROM data after a power surge 45% of cases
  2. 2
    Failing oven control board 45% of cases
  3. 3
    Intermittent supply voltage issues 10% of cases

How to Fix Electrolux Oven Error Code F13

🔧🔧🔧 Advanced DIY Est. time: 1–3 hours
⚡ Safety first: Unplug the appliance before opening any panels or touching internal components.
  1. 1

    Hard reset

    Turn off the breaker for 10 minutes so the control fully discharges, then restore power and watch the display.

  2. 2

    Check power quality

    If F13 followed a storm or brownout, consider a surge protector rated for the range circuit.

  3. 3

    Replace the EOC

    A board that re-throws F13 after a hard reset has failing memory and must be replaced.

    🔩 Electrolux oven control board (EOC) ($150–$300)
    ⚠️ Disconnect power before replacing the board — 240V circuit.

How to Reset Error Code F13

Turn off the breaker for 10 minutes, then restore power.

Note: If the error returns after resetting, the underlying issue has not been resolved. Work through the fix steps above.

Did this guide fix your appliance?

When to Call a Professional

If the code returns after a full power-down reset, board replacement is the only fix.

Average professional repair cost for this issue: $220–$420

Related Error Codes

F10
Runaway temperature detected
🛑 Critical — Stop Using
F14
Display/touch panel not communicating with the control
⚠ Medium Severity

Same Code on Other Brands

Error code F13 appears on these other brands too. See every brand that shows F13 →

Frigidaire logo
Frigidaire Oven F13
Control board internal checksum error
Miele logo
Miele Dishwasher F13
Water intake fault — dishwasher not filling

Find Replacement Parts

Use these links to find the exact replacement parts for your Electrolux Oven:

🔩
Search PartSelect
Electrolux Oven repair parts
🔧
Search RepairClinic
Step-by-step video guides

External links — ApplianceErrors.com is not affiliated with these retailers.

More Electrolux Oven Error Codes

F11 Shorted keypad key detected E11 Door latch fault — latch motor did not reach position

Frequently Asked Questions

Can I keep using my Electrolux Oven when error F13 appears? +
You often can for a cycle or two, but the control issue behind F13 will keep interrupting normal operation until it is fixed. Plan the repair rather than ignoring the code.
What most commonly causes F13 on a Electrolux Oven? +
Across reported Electrolux oven repairs, the most frequent is corrupted EEPROM data after a power surge (45% of cases), failing oven control board (45%), then intermittent supply voltage issues (10%). Check them in that order before replacing any parts.
F13 keeps coming back after a reset — what should I check next? +
A reset only clears the stored F13 fault; if it returns, the control problem is still present. Move on to the physical checks — hard reset, then check power quality — since the code will reappear until the root cause is resolved. This is an advanced repair involving deeper disassembly or electrical testing.
How much does it cost to fix Electrolux Oven error F13? +
A DIY repair typically runs $0–$300 in parts, versus $220–$420 for a professional service call, so handling it yourself saves around $220. Expect the work to take 1–3 hours.
Which Electrolux Oven models show error F13? +
F13 is documented on Electrolux wall ovens and electric ranges with an electronic oven control (EOC), broadly across models using digital control boards. Other units sharing the same control platform can display it too, so the fixes here generally transfer across the series.

Sources & References

Content verified against manufacturer service documentation. Last verified: June 11, 2026.

← All Electrolux Oven Error Codes ← All Electrolux Error Codes